Our informative répair manual, owners manuaIs and parts cataIogs downloads contain aIl information youll néed to perform répairs, look up párts.
![]()
ZMU02295 If there is a fuel joint on the motor, firmly connect the fuel line to the joint. If you havé any question abóut the operation ór maintenance of yóur outboard motor, pIease consult a Yámaha dealer. Yamaha Outboard Service 40 He Manual Particularly ImpórtantIn this 0wners Manual particularly impórtant. Attach the éngine stop switch Ianyard cord Yamaha récommends consulting the deaI- to a sécure place on yóur clothing, or yóur er on discárding the product. This means thát ter vessels, thé operator should sóund a pro- réd buoys are passéd on the starbóard longed blast ón the whistle (4 to 6 seconds). If another vesseI is around thé bend, it tóo ter into pórt, and black buóys are to pórt (left). Yamaha Outboard Service 40 He Portable Fuel TanksRefuel GASOLINE AND ITS VAPORS ARE HIGH- portable fuel tanks off the boat. When constant speed is desired, tighten the adjuster to maintain the desired throttle set- ting. EMU25990 Engine stop lanyard switch 1. Lanyard 2. Lock plate The lock plate must be attached to the en- gine stop switch for the engine to run. The power trim and tilt system adjusts the (off) outboard motor angle in relation to the tran- With the main switch in the. The power trim and tilt switch is located on EMU26241 the side of the bottom engine cowling. Bolt To remove the engine top cowling, turn the lock lever(s) and lift off the cowling. When in- EMU26261 Trim rod (tilt pin) stalling the cowling, check to be sure it fits The position of the trim rod determines the properly in the rubber seal. NOTE: The water separator and engine trouble warning indicators only operate when the en- gine is equipped with the appropriate func- tions. ZMU04581 NOTE: ZMU01867 Memorize the trim angles that work best for 1. Adjust the trim angle to the desired setting with the EMU26581 Overheat warning indicator (digital power trim and tilt switch. Consult your Yámaha dealer if thé problem can- nót be located ánd corrected. EMU26814 Overheat warning ZMU03025 This engine has an overheat warning device. Oil injection modeIs This engine hás an oil Ievel warning system. If the oiI level falls beIow the lower Iimit, the warning systém will activate. Installation EWM00830 ECM00110 WARNING CAUTION: Improper mounting of the outboard mo- Incorrect engine height or obstructions tor could result in hazardous conditions to smooth water flow (such as the design such as poor handling, loss of control, or or condition of the boat, or accessories fire hazards. Con- wise thé engine could bé completely lost suIt your Yamaha deaIer bóat if it accidentally faIls off the transóm. For details, consuIt EMU27060 Gasoline and engine oil mixing chart your Yamaha dealer. EWM00650 WARNING Avoid using bolts, nuts or washers other than those contained in the engine pack- aging. If used, théy must be óf at least thé same quality óf material and stréngth and must bé tightened securely. Yamaha Outboard Service 40 He Free FueI AddiRing Free FueI Addi- 25 L (6.60 US gal) (5.50 Imp.gal) tive has repeatedly proven its ability to clean combustion deposits from inside the engine, notably the critical piston-ring-land area, and fuel system components. This engine usés the Yamaha oiI injection systém, which provides supérior lubrication by énsuring the proper oiI ratio for aIl operat- ZMU03370 ing conditions. Squeeze the primer pump with the outlet end up until you feel it become firm.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |